| Home | Contact Us | Careers |  
 
  • 10/100 PoE extender
  • PoE (IEEE 802.3af) and PoE+ (IEEE 802.3at) compliant
  • Extension up to 600 m (1968.5 ft) using 5 GV-POEX0100
  • Compatible with GV-IP Cameras
  • No additional power supply required
Introduction
GV-POEX0100 is a single-port, 10/100 PoE extender that can extend the distance between a PoE switch and a GV-IP Camera by 100 m (328.08 ft) for every extender installed. They can be serially connected, with no additional power supply, to transmit power and data to a GV-IP Camera as far as up to 600 meters (1968.5 ft) away from a PoE switch.
  • Requirements
  • Specifications
  • Packing List
  • Download
  • Ordering Info

The maximum distance allowed between a PoE switch and a GV-IP Camera depends on the PoE switch type, PoE power output of the connected device (PD) and the type of power supply. These can be summarized below.

GV-IP Cameras Powered by PoE
  Brand & Model
PD of GV-IP Cameras GeoVision Third-Party PoE Switches
(IEEE 802.3at)
GV-POE0801 / 0811
GV-POE0812
GV-POE1601 / 1611
GV-POE2401 / 2411
GV-POE0400
GV-POE0410-E
GV-POE0800
GV-POE0810
PD < 6.49 W
(IEEE 802.3af)
600 m (1968.5 ft) 400 m (1312.34 ft) 400 m (1312.34 ft)
PD 6.5 W ~ 12.95 W
(IEEE 802.3af)
400 m (1312.34 ft) 200 m (656.17 ft) 200 m (656.17 ft)
PD 13 W ~ 25.5 W
(IEEE 802.3at)
200 m (656.17 ft) - -
PD > 25.5 W - - -
Note:
  1. Each GV-POEX0100 extends another 100 m (328.08 ft) between the PoE switch and the GV-IP Camera. Therefore, a distance of 200 m (656.17 ft) requires one GV-POEX0100 and 400 m (1312.34 ft) requires three etc.
  2. GV-POE0100 can only be connected using CAT-5e cables, TIA/EIA-568-B, with the maximum DC resistance of 9.38 ohms/100 m.

GV-IP Cameras Powered by Power Adapters
Brand & Model GeoVision Third-Party PoE Switches
(IEEE 802.3at)
GV-POE0801 / 0811
GV-POE0812
GV-POE1601 / 1611
GV-POE2401 / 2411
GV-POE0400
GV-POE0410-E
GV-POE0800
GV-POE0810
GV-IP Cameras 600 m (1968.5 ft) 400 m (1312.34 ft) 400 m (1312.34 ft)

Compatibility

  1. GV-POEX0100 is only compatible with third-party switches that comply to PoE+ (IEEE 802.3at) and is not compatible with GV-PA191/481/482/901.
  2. GV-POEX0100 supports all GV-IP Cameras when installed with a power adapter and does not support the following models when powered by PoE:
    • GV-BX2510-E / 5310-E
    • GV-FE3403 / 5303
    • GV-VD2540-E / 5340-E
    • GV-SD220 / 220-S
  3. GV-POEX0100 is only compatible with the following GeoVision PoE switches of the indicated firmware versions:
    • GV-POE0801 / 1601 / 2401 (V1.03 or later)
    • GV-POE0811 / 1611 / 2411 (V1.01 or later)

Ports
Network Standard 10/100 Mbps half/full duplex
Connectors RJ-45
Network cables Cat5e or higher
Mechanical
LED Indicator 4 LEDs: Power x2, Network x2
Power indicator: PoE enable (Amber)
Network indicator: Link (Green), Activity (Green Blink)
PoE Control Button On / Off
General
Operating Temperature -10°C ~50°C (14°F ~ 122°F)
Humidity 10% to 90% (no condensation)
Environment Indoor
Dimensions (L x W x H) 102.8 x 28.8 x 20 mm (4.05" x 1.13" x 0.79")
Weight 87 g (0.19 lb)
Regulatory CE, FCC Class A
Note: Specifications are subject to change without prior notice.

  1. GV-POEX0100
  2. Screw x 2
  3. Screw anchor x 2
  4. GV-POEX0100 Installation Guide
 
Installation Guide pdf
Datasheet pdf


Item No. (Sales Part No.) Description
{item} {Des}

  © 2015 GeoVision Inc. All Right Reserved. Warranty | Terms of Use | Reporting Piracy